Randy Ayers Nascar Modeling Forums Forum Index Randy Ayers Nascar Modeling Forums

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

1976 Torino, Bud Moore style (5/6/21 update)

 
Post new topic   Reply to topic    Randy Ayers Nascar Modeling Forums Forum Index -> The Fab Shop
View previous topic :: View next topic  
Author Message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Fri Mar 01, 2019 7:36 pm    Post subject: 1976 Torino, Bud Moore style (5/6/21 update) Reply with quote

As a Ford fan in the '70s, I respected the brilliant white Bud Moore Torinos, driven by Buddy Baker. As the '76 season approached, I anticipated the mandated change to the notchback coupe, as the fastback Torinos were now too old.

The Torino, from 1972 to 1974 had gone through an awkward transition, from sleek to bulky. It was the Mickey Rourke of cars. However, Bud Moore made the bulky '74-'76 look slick.

The body-in-red here the S&H Torino. Nice but with some subtle inaccuracies. The front is a little to 'square.' the side windows seem a bit small. Not difficult to correct.

I am in the rough beginning stages. Opened up and flaring the front wheel openings, modified the front lower fender surfaces, removed the bumper mountings front and rear, sectioned the bumpers to narrow them, removed bumper guards.


_________________
Bill Jobson is my real name.


Last edited by Firefly on Thu May 06, 2021 11:46 am; edited 6 times in total
Back to top
View user's profile Send private message
DaveVan



Joined: 27 Jan 2018
Posts: 1571

PostPosted: Fri Mar 01, 2019 8:55 pm    Post subject: Reply with quote

Good start!!!! FYI the 'stock' version is molded in white if you build more of these.
Back to top
View user's profile Send private message Send e-mail
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Fri Mar 01, 2019 9:01 pm    Post subject: Reply with quote

DaveVan wrote:
... FYI the 'stock' version is molded in white if you build more of these.


Yeah - I got this cheap on Ebay, so I know I'll be putting silver spray paint on my Lowe's list....
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
DaveVan



Joined: 27 Jan 2018
Posts: 1571

PostPosted: Fri Mar 01, 2019 11:02 pm    Post subject: Reply with quote

Yeah....the silver covers that red fine....even on a light blue paint....
Back to top
View user's profile Send private message Send e-mail
BW



Joined: 01 Feb 2018
Posts: 218
Location: Lick Creek, Alabama

PostPosted: Sat Mar 02, 2019 10:24 pm    Post subject: Reply with quote

Nice work firefly! Really like the flared wheel openings. Keep it comin'!
Bobby
Back to top
View user's profile Send private message
"Fireball"



Joined: 09 Feb 2018
Posts: 202

PostPosted: Sun Mar 03, 2019 10:45 pm    Post subject: Reply with quote

May I ask what chassis configuration are you planning on using under your build? Thanks for sharing.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Mon Mar 04, 2019 7:36 pm    Post subject: Reply with quote

"Fireball" wrote:
May I ask what chassis configuration are you planning on using under your build? Thanks for sharing.


I am going with a Monogram T-bird, which fits well, but will need to lower the dash.
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
AdamtheWayne



Joined: 09 Jul 2018
Posts: 1182

PostPosted: Mon Mar 04, 2019 9:07 pm    Post subject: Reply with quote

Firefly wrote:
"Fireball" wrote:
May I ask what chassis configuration are you planning on using under your build? Thanks for sharing.


I am going with a Monogram T-bird, which fits well, but will need to lower the dash.
I was going to suggest that. I have the same kit, cheap from ebay, after watching the movie... lost my taste for the car as is. Rolling Eyes So I'll be following this one with interest as well. Please feel free to make any of my mistakes for me. Laughing
_________________
"Dude, it's not Camelot... it's only a model." "Details man, I need details!!"
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Tue Mar 05, 2019 9:37 pm    Post subject: Reply with quote

AdamtheWayne wrote:
...Please feel free to make any of my mistakes for me. Laughing


With gusto! Very Happy
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
afx



Joined: 28 Jan 2018
Posts: 270

PostPosted: Thu Mar 07, 2019 1:04 pm    Post subject: Reply with quote

I'll be following as a dyed in the wool blue oval fan.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Fri Mar 08, 2019 9:35 am    Post subject: Reply with quote

afx wrote:
I'll be following as a dyed in the wool blue oval fan.


I was so dyed in the wool in those days I 'modified' a Matador AFX body to a Junie Torino. Just dug this up recently...

_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
"Fireball"



Joined: 09 Feb 2018
Posts: 202

PostPosted: Sat Mar 09, 2019 5:33 pm    Post subject: Reply with quote

Firefly wrote:
afx wrote:
I'll be following as a dyed in the wool blue oval fan.


I was so dyed in the wool in those days I 'modified' a Matador AFX body to a Junie Torino. Just dug this up recently...


I'm right there with you guys!!! That AFX Matador body didn't by any chance start out as a yellow cab, did it? Mine did, and by the time I was done cutting, filing, sanding, and exacto scraping on it, Penske's real race car looked stock compared to my aero Matador. I hear you clucking, and I know where your nest is!!!
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Sat Mar 09, 2019 8:26 pm    Post subject: Reply with quote

[quote=""Fireball""... That AFX Matador body didn't by any chance start out as a yellow cab, did it? [/quote]

Mine was the racing version (not the Penske scheme).
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Fri Jun 21, 2019 5:55 pm    Post subject: Reply with quote

I've primed over the red, so the work on the wheel openings is easier to visualize here. The shot from the rear has poor focus, but you can see the basic shape of the front wheel opening bulge.


_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Danno



Joined: 18 Apr 2019
Posts: 8

PostPosted: Wed Jul 03, 2019 10:56 am    Post subject: Reply with quote

What kind of putty do you use for the flares? Does it shrink over time?
Back to top
View user's profile Send private message
AdamtheWayne



Joined: 09 Jul 2018
Posts: 1182

PostPosted: Wed Jul 03, 2019 11:44 am    Post subject: Reply with quote

Looks like Tamiya white. I don't believe it shrinks. Nice work so far. The subtle flares look really good.
_________________
"Dude, it's not Camelot... it's only a model." "Details man, I need details!!"
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Thu Jul 04, 2019 7:44 am    Post subject: Reply with quote

Danno wrote:
What kind of putty do you use for the flares? Does it shrink over time?


Hey Danno. Tamiya White. I finish with a coat of Tamiya Liquid Surface Primer (in the square bottle) which I also use to smooth edges and fill pinholes or small recesses. Haven't had shrinking issues once dried.
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Fri Jul 26, 2019 5:32 pm    Post subject: Reply with quote

Test fitting the narrowed bumpers. As with typical '70s bumpers these get tucked in much deeper than stock. Bud had the rear nearly flush with the trunk valance panel.


As you can see, I still need to add the taillight covers, etc. Still refining the bodywork details...
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Thu Jul 23, 2020 6:23 pm    Post subject: Reply with quote

Been a year since my last update. Juggling other stuff...anyway, I have spent more time studying photos of the actual race car, and am discovering the magic that Bud Moore had applied to this brick of a car to smooth it out and cheat the wind where possible. Also looking more closely at the accuracy of the Revell body in general. Did some Photoshop work:

This is a nice side view of the Revell S&H body, originally posted somewhere else by someone else. The credit is theirs.


I laid over a 1:1 Torino, to check accuracy to the factory body:

The only two things that stood out are the side window, which is cut a little high, and the nose, which points up just a bit. The lower front fenders, between the bumper and wheel opening should angle down a bit more toward the wheel opening.

Here is the Bud Moore car:


And laid over the Revell:

Some serious droop there.

How could this pass a template check? I studied some shots from the front.
Note how the arc of the back edge of the hood- at the windshield -drops at the left and right. (I added the horizontal guidelines). This keeps the center line of the hood at a higher level, and the sides drop to follow the drop of the fenders.


Compare to a S&H movie Torino:



This rear angle betrays the body massaging done on those front fenders. The top top creases of the fenders disappear beyond the A-pillar:


Time to once again get out the hobby saw, emory boards and putty...
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
George Andrews



Joined: 30 Jan 2018
Posts: 458

PostPosted: Sun Jul 26, 2020 10:53 am    Post subject: Reply with quote

Excellent seminar so far; the body overlays are great! Worth noting that during this time period the Chevrolet Laguna S-3 was by far the slickest car body allowed by NASCAR, putting the Mopar & Fomoco teams ( except maybe The Wood Brothers ) behind in Superspeedway Areo. I'm guessing that NASCAR, in their never - ending efforts to keep the competition equal, turned a blind eye to some of the body massaging efforts. Photos I have show Cup & West Series cars going through Tech Inspection at Riverside. Richard Petty's # 43 Buick had a gap in the front of the full body template that one could fit their hand under !!! Laughing
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Thu Sep 10, 2020 8:39 pm    Post subject: Reply with quote

So I sawed along the front edge of the door, starting at the bottom and working about 3/4 the way up. Then rejoined at the bottom, to droop the front just a bit. Then warmed the front and gave it just a bit of bend at the wheel arch. The front fascia was made right to the road by sawing the seam at the headlamp caps, and bending the fascia back up and perpendicular to the road.


Sanded a bit off the fender top creases - this is more like it.


Fenders flared.

_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Bill J



Joined: 28 Jan 2018
Posts: 392

PostPosted: Thu Sep 10, 2020 9:44 pm    Post subject: Reply with quote

Nice work Bill Smile
Back to top
View user's profile Send private message
afx



Joined: 28 Jan 2018
Posts: 270

PostPosted: Fri Sep 11, 2020 7:00 am    Post subject: Reply with quote

Coming along nicely.
Back to top
View user's profile Send private message
steveracer



Joined: 11 Oct 2020
Posts: 47

PostPosted: Tue Nov 24, 2020 10:48 pm    Post subject: Reply with quote

I'm Following this one! I wondered how that GTorino body was from the kit, and looks like you modified about 60 percent of it to get it into racing shape!

Look forward to more updates, Bill, this one should look cool.
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Wed Nov 25, 2020 7:43 pm    Post subject: Reply with quote

steveracer wrote:
I'm Following this one! I wondered how that GTorino body was from the kit, and looks like you modified about 60 percent of it to get it into racing shape!

Look forward to more updates, Bill, this one should look cool.


Thanks. Bud Moore really slicked up the Torino body more than other racers I have noticed. I am working on a '72 RC Cola car as well, and there was some work up front on that one too.
_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
Mack



Joined: 28 Jan 2018
Posts: 731
Location: deep south

PostPosted: Wed Nov 25, 2020 9:55 pm    Post subject: Reply with quote

Looking mighty fine!!!!
_________________
life is hard, it's harder when you're stupid. John Wayne
Back to top
View user's profile Send private message
Firefly



Joined: 28 Jan 2018
Posts: 808
Location: New Jersey

PostPosted: Thu May 06, 2021 11:44 am    Post subject: Reply with quote

Finally got it painted (with brush!) Tamiya white. The car I am doing required some extra decal creation, so I did them in Adobe Illustrator and printed inkjet on Sunnyscopa clear decal film. Will add the LoboGraphix elements and contigencies.

_________________
Bill Jobson is my real name.
Back to top
View user's profile Send private message
MarkJ



Joined: 29 Jan 2018
Posts: 1296

PostPosted: Thu May 06, 2021 1:39 pm    Post subject: Reply with quote

Man, Bill. That came out perfect.
Back to top
View user's profile Send private message
nolansims1



Joined: 14 Apr 2021
Posts: 14

PostPosted: Fri May 07, 2021 10:38 am    Post subject: Reply with quote

looks great!
Back to top
View user's profile Send private message
Pierre Rivard



Joined: 25 Feb 2021
Posts: 378
Location: Montreal, Canada

PostPosted: Fri May 07, 2021 4:15 pm    Post subject: Reply with quote

It looks beautiful Bill. I look forward to future updates.
I admire your extensive body modifications.
great work!
_________________
"When you arrive at a fork in the road, take it" - Yogi Berra
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Randy Ayers Nascar Modeling Forums Forum Index -> The Fab Shop All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group